Quick Answer: Can I Put Too Much Bleach In My Well?

What happens if you put too much bleach in well?

A small amount of chlorine won’t hurt a septic system, but a large amount (e.g.

a gallon put in all at once) can kill the bacteria that you *do* want in that system.

– IMPORTANT – if you have a water softener system – bypass it when doing the sanitization..

How long should you wait to use water after you chlorinate a well?

Let the chlorinated water stand in the plumbing system for 12 to 24 hours. Do not run any water or flush toilets during this time. Use your reserves of fresh water for all purposes. Step 6 WAIT at least 12 hours before turning faucets back on.

How much bleach do you use to shock a well?

Mix 2 quarts bleach in 10 gallons of water; pour into well. Connect a garden hose to a nearby faucet and wash down the inside of the well.

How long after bleaching Well can I shower?

24 hoursBefore you chlorinate your well, there are a number of precautions and steps to take to ensure safety for your family. Keep in mind that doing laundry and taking a shower cannot be done for at least 24 hours with a chlorinated well. Waiting a few days to do these is a good idea.

How much does it cost to have a well cleaned?

How much will Hydrofracturing cost? Standard Hydrofracturing service to a residential well will run in the $2000 to $3000 range by the time everything is put back together and finished. Zone fracturing service to a residential well will usually run in the range of $5000 to $7000 when finished and put back together.

How often should you chlorinate your well?

Have a professional check your well water every three to five years to ensure it’s free of dangerous microbes. If their tests do reveal the presence of microbes, order a complete well chlorination. Chlorine treatment will remove all toxic bacteria and algae, with only minimal disruption to your water supply.

How long does it take to smell bleach when shocking a well?

It can take 30 minutes to 24 hours or more to flush all of the chlorine from the well. ►Once the chlorine is gone from the well, open up each fixture one at a time until the chlorine smell is no longer present.

How do you sanitize a deep well?

CLEAN: Remove all loose or foreign debris from the well house, spring house or storage tank. Turn the pump circuit breaker off and remove the well cap or cover. Then scrub the accessible interior surface with strong chlorine solu- tion (1/2 gallon chlorine bleach per 5 gallons clean water).

Is shocking a well Necessary?

Bacteria clogs pipes by building up on their sides, congregating thickly and keeping water from pushing through adequately. In order to unclog your pipes, it is necessary to remove any and all iron bacteria which may be present in your well system. This will typically require a shock chlorination.

Should you add chlorine to well water?

Over time, however, the well can become contaminated with bacteria and other harmful pathogens. One effective treatment for this is to add chlorine bleach to the well water, which will kill the bacteria.

How often should you add bleach to your well?

4) Work out how much bleach will be needed: For every 50 gallons of water in the well use one quart of laundry bleach – (4 quarts in a gallon). Do not use excessive amounts of bleach – more is not more effective. 5) For best results the bleach should be combined with water before adding it to the well.

Can I pour hydrogen peroxide in my well?

From time to time, it may be desirable to use hydrogen peroxide to decontaminate the entire well because some of the odor-causing bacteria also produce sulfuric acid, which will corrode the pump in the long run. Some of the iron bacteria can also produce a musty, fishy or oily smell in the water.

Can I use pool shock in my well?

The best way to shock chlorinate a well is to use a combination of dry pellets and dry chlorine granules mixed with water. The dry pellets drop down past the pump and ensure the entire well is sanitized. … You can also use pool chlorine, which is 10% to 12% sodium hypochlorite and twice as strong as household bleach.

Can I dump bleach in my well?

Chlorinate the well. Ⅰ Use household bleach which typically has a chlorine concentration of 6%. … Ⅰ Mix bleach in a bucket of water. Remove well cap, plug, or vent (see diagrams on page 2); using a funnel, pour the bleach into your well.

Will Shocking well get rid of sulfur smell?

1. Shock your well with chlorine bleach or hydrogen peroxide to get temporary relief from sulfur odors. Often keeps odors away for 1 – 2 months. 2.

Why does my well water turn brown when I add bleach?

The brown is the iron in the water that has oxidized as a result of the chlorination. Normally, the iron in water is in ion form and does not display itself until it combines with oxygen and forms common rust which turns the water reddish-brown.

Why do you chlorinate a well?

Chlorinating a well eliminates other water quality problems, as well, like the presence of iron bacteria and hydrogen sulfide. These contaminants can give the water a bad taste and cause a rotten egg smell when the faucet is turned on.

How long does it take for water to clear after shocking a well?

Run the water to flush the bleach solution out of the well. Monitor the process, it can take 30 minutes to 24 hours or more to flush all of the bleach solution from the well. Use chlorine test papers to verify that the water coming from the outside faucet or yard hydrant is clear of any bleach solution.